Laurel hedge pruning in Littlebourne: the decision route.
Laurel is one of the most common evergreen hedging plants in Littlebourne gardens, and also one of the most frequently butchered with the wrong tool. Whether you have cherry laurel or Portuguese laurel makes a real difference to how you cut it and what the result looks like.
Step 1: which laurel hedge do you have?
Cherry laurel (Prunus laurocerasus): large, wide, glossy leaves, typically 10–15 cm long, with a rounded tip and finely toothed edge → the leaf size is the key detail that determines your tool choice. A hedge trimmer or hand shears will bisect many of those large leaves midway through, leaving half-leaves with brown, dead-looking cut edges that are visible for weeks until new growth covers them. Go to Step 2 before deciding how to cut.
Portuguese laurel (Prunus lusitanica): smaller, darker, oval leaves, typically 5–8 cm long, with reddish leaf stalks and a more pointed tip → the smaller leaf size means a hedge trimmer cuts cleanly between leaves rather than through them in most cases. You can clip Portuguese laurel with shears or a powered trimmer in the same way you would a box or beech hedge. Go straight to Step 3.
If you are not certain which species you have, a nursery identification or a search on the RHS plant finder using a photo of the leaf will confirm it. Both species are widely planted throughout Littlebourne, Bekesbourne and Patrixbourne as boundary and garden division hedges.
Step 2: tools for cherry laurel (the choice that decides the finish)
This step applies to cherry laurel only. If you have Portuguese laurel, go to Step 3.
Using a powered hedge trimmer or hand shears on cherry laurel → acceptable for the top of the hedge where appearance is less critical, or for an overgrown hedge you are cutting back hard as a renovation and plan to let regrow from scratch anyway. On visible side faces, the bisected leaves leave a noticeable brown patchy surface. It is not a permanent problem, since new growth covers the cuts within a few weeks in the growing season, but it looks poor immediately after cutting.
Using secateurs or bypass loppers on cherry laurel → the right tool for any face you need to look clean straight after cutting. Secateurs let you make individual cuts between leaves rather than through them, so the hedge surface stays green. The work is slower per metre, but on a garden boundary hedge in Littlebourne where the finished appearance matters, the difference is obvious. For a long hedge run, the practical approach is secateurs on the prominent front face and a trimmer on the back and top.
Step 3: what type of work does the laurel hedge need?
Annual maintenance trim to hold the existing size and shape → go to Step 4 for timing. Both cherry and Portuguese laurel grow vigorously and a single cut per year is the minimum to keep a hedge from spreading significantly.
A genuine size reduction, 20 cm or more per face, back into woody growth → both cherry laurel and Portuguese laurel regenerate reliably from old bare wood. This is a significant practical difference from leylandii and other conifers: you are not restricted to cutting within the green outer surface. See the leylandii reduction decision route if you have a mixed boundary with conifer sections, as the rules are very different. For laurel, go to Step 4 for the timing of a reduction cut.
Full hard renovation, the hedge has become too large over many years and needs cutting back near to the main stems → cutting cherry laurel back to within 30–60 cm of the ground is a genuine option. The established root system pushes strong new shoots through the following spring. Portuguese laurel responds equally well. Go to Step 4 for the right timing.
Step 4: when to cut?
Annual maintenance trimming → late May to June is the best first cut of the year, once the spring growth flush has extended and before it becomes untidy. A second cut in late August to early September gives a tidy finish going into autumn. Both windows sit partly inside the nesting season: go to Step 5 for the nesting check before cutting between 1 March and 31 August.
Hard renovation or significant reduction → February to mid-March is the recommended window, cutting before the buds break so the plant channels its first spring energy directly into the new growth you want. Cutting in late summer (August to September) is also feasible for renovation if February passes without action, though recovery before winter is less complete. A renovation cut made in late spring or early summer will push new growth but leaves very little time for it to harden before the first frosts, so February or August are the two preferred windows.
Any cutting between 1 March and 31 August requires a nesting check: go to Step 5.
Step 5: the nesting-season check
1 September to end of February → outside the main nesting season. This is the safest window for cutting laurel hedges without a formal nest check, and the preferred window for any renovation or heavy reduction work.
1 March to 31 August → a competent nest check is required before any cutting under section 1 of the Wildlife and Countryside Act 1981, which makes it an offence to intentionally damage or destroy an active nest. Dense cherry laurel hedges are commonly used as nesting cover by blackbirds, robins and song thrushes throughout this period. Many of the longer laurel boundary hedges around Littlebourne and the surrounding Little Stour valley settlements back onto gardens or orchard edges that provide foraging habitat, making them actively attractive nesting sites from late March through to July. A visual check at a distance is not sufficient: inspect from multiple angles, including through any gaps, before starting work. The full nesting-season decision route covers the check step by step.
If the laurel hedge stands within Littlebourne’s conservation area, or in a neighbouring village with its own designation, check whether a tree standing in or grown out of the hedge has a stem over 75 mm diameter at 1.5 m height. If so, six weeks’ written notice to Canterbury City Council is required under section 211 of the Town and Country Planning Act 1990 before any work starts. We include this check and file the notice on your behalf as part of every quote for conservation-area work. If you are unsure whether your property falls within a designation, see the conservation area decision route for the address check.
Not sure whether to use secateurs or a trimmer on your laurel hedge?
Send a photo and your postcode to hello@littlebournehedges.co.uk or call 07763 100 477. We will tell you what the hedge needs before we quote anything.
Sources: Hedging Plants Direct UK – How to Prune and Cut back a large Laurel Hedge (YouTube); RHS – Cherry Laurel pruning guide; Wildlife and Countryside Act 1981, section 1; Town and Country Planning Act 1990, section 211.